| Item information | Value |
|---|---|
| Category: | Type 2875 Direct-acting 2-way standard proportional valve |
| Valve seat seal material: | EPDM (ethylene-propylene diene rubber) |
| Operation: | direct-acting |
| Nominal pressure max: | 8 bar |
| Port connection 1 type: | Flange |
| Kv value (water): | 0,45 m3/h |
| Electrical connection type: | Plug pattern form A according to DIN EN 175301-803 |
| Main valve orifice size 1 (P) (mm): | 4 mm |
| Main valve media-contacting material: | Stainless steel |
| Voltage min / nominal voltage: | 24 V |
| Port connection 1 flange: | Bürkert flange 45 x 45 version A1 |
| Degree of protection IP (max. with suitable connection): | IP65 |
| Nominal power: | 16 W |
| Item weight: | 0,92 kg |
Direct-acting 2-way standard proportional valve
The direct-acting proportional valve Type 2875 is used as the regulating unit in control loops. Due to an elastomeric seat seal the valve closes tight (integrated shut-off function), up to the DN specific nominal pressure. The plunger of the valve is assembled frictionless, which leads to an extraordinary adjustment characteristic. This valve is particularly suitable for demanding control tasks (high control range, dry gases, etc.).
Technical data
Function (9)
| Type | 2875 |
| Valve function | A - normally closed - inlet port 1 (P/NC) |
| Fluidic port connection quantity | 2 |
| Valve function quantity switch positions | 2 |
| Operation | direct-acting |
| Main valve function principle | Globe valve |
| Switch function | proportional |
| Flow direction | Below seat |
| Installation position | any |
Orifice & flow (5)
| Main valve orifice size 1 (P) (mm) | 4 mm |
| Main valve orifice size 1 (inch) | 5/32 inch |
| Kv value (water) | 0,45 m3/h |
| QNn value (gas) | 485 l/min |
| Control range | 1:100 |
Pressure & temperature (7)
| Nominal pressure min | -1 bar |
| Nominal pressure max | 8 bar |
| Differential pressure max | 8 bar |
| Medium temperature min | -30 °C |
| Medium temperature max | 90 °C |
| Environment temperature min | -30 °C |
| Environment temperature max | 55 °C |
Line connection (6)
| Port connection 1 type | Flange |
| Port connection 1 flange | Bürkert flange 45 x 45 version A1 |
| Port connection 2 type | Flange |
| Port connection 2 flange | Bürkert flange 45 x 45 version A1 |
| Mounting (flange) type | Metric screws |
| Mounting (flange) material | Stainless steel |
Materials (11)
| External sealing material | EPDM (Ethylene-propylene-diene rubber) |
| Valve seat seal material category | Elastomers |
| Valve seat seal material | EPDM (Ethylene-propylene-diene rubber) |
| Main valve media-contacting material | Stainless steel |
| Media-contacting part press-fit seat material | Stainless steel |
| Media-contacting part core material | Stainless steel |
| Media-contacting part stopper material | Stainless steel |
| Media-contacting part core guide tube material | Stainless steel |
| Media-contacting part core guide element 1 material | Stainless steel |
| Media-contacting part core guide element 2 material | PEEK (Polyetheretherketone) |
| Media-contacting part spacer sleeve material | Stainless steel |
Actuator & coil (10)
| Actuator type | Plunger valve |
| Core guide | Shaped spring |
| Core guide 2 | Bush |
| Coil type | block bolted |
| Coil insulation material (encasement) | Epoxy |
| Coil size | 49 mm |
| Coil resistor | 21,4 Ohm |
| Thermal insulation class of the actuator | H |
| Nominal power | 16 W |
| Nominal operating mode / duty cycle | 100 % |
Electrical (14)
| Voltage min / nominal voltage | 24 V |
| Voltage max / nominal voltage | 24 V |
| AC voltage | No |
| DC voltage | Yes |
| Voltage tolerance positive | 10 % |
| Voltage tolerance negative | 10 % |
| Degree of protection IP (max. with suitable connection) | IP65 |
| Electrical connection type | Plug pattern form A according to DIN EN 175301-803 |
| Electrical connection number of contacts | 2 + Grounding conductor |
| Electrical connection design | male |
| Cable plug in scope of delivery | not included |
| Electrical connection position | in direction of flow left |
| PWM frequency min. | 400 Hz |
| PWM frequency max. | 500 Hz |
Versions (7)
| Vacuum variant | No |
| Analysis variant | No |
| Oxygen variant | No |
| Steam variant | No |
| Media separation | No |
| suitable for liquid media | Yes |
| suitable for gaseous media | Yes |
Shipping & customs (4)
| Weight | 0,915 kg |
| Customs tariff number | 84818079 |
| Country of origin | Germany |
| Export | Not subject to export licensing |
Product benefits
- Excellent range
- Very good response
- Compact valve design
- Orifice sizes 2...9.5 mm
- Optional: Explosion-protected coil
Your Benefits With Us
- Worldwide shipping of all valves and flow meters
- Large stock levels for many products – current lead time available on request
- Spare parts and service kits available
- Fast shipping via UPS (parcel) or freight forwarder (pallets), express delivery available on request
- Extensive hands-on application know-how
- Personal advice on selecting the right component
- Resellers receive volume-based discounts on request
- Large companies, public authorities and government agencies can order on account (request via our contact form)
Christian Bürkert GmbH & Co. KG, Christian-Bürkert-Straße 13-17, 74653 Ingelfingen, Baden-Württemberg, Deutschland, [email protected]
Manufacturer according to GPSR
Christian Bürkert GmbH & Co. KG, Christian-Bürkert-Straße13-17, 74653 Ingelfingen, Baden-Württemberg, Deutschland, [email protected]
