Product Description
Schmersal AZM150SK-02/02RA-024 – Solenoid interlock of the AZM150 series. It keeps the movable guard locked until the hazardous condition has ended and signals position and locking status to the safety controller. The manufacturer's article number is 153032126, the EAN 4030661689036.
Field of application
Suitable for removable guard, hinged safety guard, sliding safety guard.
Scope of delivery
Slot cover for dust-proof covering of the opening not in use / Actuator must be ordered separately.
Important note
Interlocks with the power to lock principle may only be used in special cases after a thorough evaluation of the accident risk, since the guarding device can immediately be opened on failure of the electrical power supply or when the main switch is opened
Technical data
Safety-related characteristic data (14)
| Standards |
EN ISO 13849-1 |
| Performance Level, up to (single channel) |
c |
| Category (single channel) |
1 |
| Precondition for the fault exclusion |
Can be used when fault exclusion for dangerous damage to the 1-channel mechanism is permissible and sufficient protection against manipulation is guaranteed. |
| Performance Level, up to (with fault exclusion) |
d |
| Category (with fault exclusion) |
3 |
| Precondition for category 3 |
for 2-channel use and with suitable logic unit. |
| B10D Normally-closed contact (NC) |
2,000,000 Operations |
| Note on the NC contact |
Electrical life on request. |
| B10D Normally-open contact (NO) |
1,000,000 Operations |
| Note on the NO contact |
at 10% Ie and ohmic load |
| Mission time |
20 Year(s) |
| Coding level according to EN ISO 14119 |
Low |
| Mission time |
20 Year(s) |
Interlocking and actuation (10)
| Holding force FZh in accordance with EN ISO 14119 |
1,500 N |
| Holding force Fmax, maximum |
1,950 N |
| Manual release |
Yes |
| Note (Manual release) |
By means of M5 triangular key / For maintenance, installation, etc. |
| Number of actuating directions |
2 |
| Actuating speed, maximum |
0.3 m/s |
| Positive break travel |
5 mm |
| Positive break force per NC contact, minimum |
10 N |
| Mechanical lifetime, minimum |
1,000,000 Operations |
| Latching force, approx. |
50 N |
Contacts and connection (12)
| Switching element |
Magnet: 2 NC contacts / Actuator: 2 NC contacts |
| Number of safety contacts |
4 |
| Switching principle |
slow action, positive break NC contact |
| Material of the contacts, electrical |
Silver |
| Terminal (mechanical) |
Screw terminals |
| Cable entry |
3 x M20 x 1,5 |
| Cable section, minimum |
0.25 mm² |
| Cable section, maximum |
1.5 mm² |
| Note |
including conductor ferrules without plastic collar |
| Allowed type of cable |
solid single-wire / solid multi-wire / flexible |
| Tightening torque of electrical connection, minimum |
0.6 Nm |
| Tightening torque of electrical connection, maximum |
0.8 Nm |
Electrical data (15)
| Rated control voltage |
24 VDC |
| Electrical power consumption, maximum |
8.5 W |
| Magnet switch-on time |
100 % |
| Rated insulation voltage Ui
|
300 V |
| Rated impulse withstand voltage Uimp
|
4 kV |
| Thermal test current |
5 A |
| Required rated short-circuit current |
1,000 A |
| Voltage, Utilisation category DC-13 |
24 VDC |
| Current, Utilisation category DC-13 |
4 A |
| Voltage, Utilisation category AC-15 |
230 VAC |
| Current, Utilisation category AC-15 |
4 A |
| Maximum switching frequency |
1,000 /h |
| Test pulse duration, maximum |
5 ms |
| Test pulse interval, minimum |
50 ms |
| Protection class |
II |
Design, material, environment (18)
| Working principle |
electromechanical |
| Housing material |
Plastic, glass-fibre reinforced thermoplastic, self-extinguishing |
| Length of sensor |
48 mm |
| Width of sensor |
40 mm |
| Height of sensor |
204 mm |
| Gross weight |
594 g |
| Mounting |
Screws |
| Type of the fixing screws |
4x M5 |
| Tightening torque of the fastening screws for the housing cover |
0.5 Nm |
| Note |
Torx T10 |
| IP Degree of protection |
IP67 / IP65 |
| Ambient temperature |
-25 ... +55 °C |
| Storage and transport temperature |
-40 ... +85 °C |
| Note (Relative humidity) |
non-condensing / non-icing |
| Property class |
8.8 |
| Material of the latching bolt |
Stainless steel (1.4104) |
| Tightening torque of the fixing screws, maximum |
1.5 Nm |
| Tightening torque of the fixing screws, minimum |
1.3 Nm |
Standards and approvals (4)
| Standards |
EN IEC 60947-5-1 / EN ISO 13849-1 / EN ISO 14119 |
| Certificates |
cULus / TÜV / CCC |
| eCl@ss number, version 12.0 |
27-27-26-03 |
| ETIM number, version 7.0 |
EC002593 |
Weitere Angaben (5)
| Relative humidity, maximum |
93 % |
| Degree of pollution |
2 |
| Overvoltage category |
II |
| Note (Mechanical lifetime) |
from device version V2 (see type plate) |
| Note (Switching element) |
galvanically separated contact bridges |
Delivery time and availability
Many items of this series are available from stock; special versions are built to order by the manufacturer and take correspondingly longer. The delivery time shown in the shop applies to stocked goods and is a guide value. For urgent orders please ask us for the actual delivery time in advance – we will also check whether express shipping is possible.
Your advantage when buying from us
- Authorised Schmersal dealer — genuine products with full manufacturer warranty
- Technical advice from specialists in machine safety
- All safety-related characteristic data documented for your risk assessment
- Matching actuators and accessories from a single source
- A named contact instead of an anonymous ticket system
- Shipping from Germany, delivery throughout Europe
