| Item information | Value |
|---|---|
| Category: | Type 6650 Solenoid Valve |
| Fluidics body material: | PEEK (Polyetheretherketone) |
| Seat seal material: | FFKM (Perfluoroelastomer rubber) |
| Line connection 1: | Flanged-Bürkert flange 4,5 x 39 version A1 |
| Voltage max / rated voltage: | 24 V |
| Nominal pressure min: | -1 bar |
| Operation: | direct-acting |
| Valve function: | A - normally closed - inlet port 1 (P/NC) |
| Nominal pressure max: | 3 bar |
| Temperature medium: | 15 °C-50 °C |
| Fluidic port connection number: | 2 |
| Valve function number of switching positions: | 2 |
| Valve function: | A - normally closed - inlet port 1 (P/NC) |
| Manual actuation: | No |
| Port connection 1 type: | Flanged |
| Port connection 2 type: | Flanged |
| Type: | 6650 |
| Voltage min / rated voltage: | 24 V |
| Voltage max / rated voltage: | 24 V |
| AC voltage: | No |
| Fluidics body material: | PEEK (Polyetheretherketone) |
| DC voltage: | No |
| Battery voltage: | Yes |
| Nominal pressure max: | 3 bar |
| Differential pressure max: | 3 bar |
| Nominal pressure min: | -1 bar |
| Temperature medium min: | 15 °C |
| Temperature medium max: | 50 °C |
| Temperature environment min: | 10 °C |
| Temperature environment max: | 50 °C |
| Seat seal material category: | Elastomer |
| Seat seal material: | FFKM (Perfluoroelastomer rubber) |
| Sealing toward outside material: | FFKM (Perfluoroelastomer rubber) |
| Valve diameter: | 0,8 mm |
| Rated power consumption: | 5 W |
| Kv value (water): | 0,01 m3/h |
| Actuator type: | Pivot |
| Operation: | direct-acting |
| Media separation: | Yes |
| Minimum holding power: | 0,7 W |
| Flow: | Above seat |
| Time-of-use period/length: | 0,5 min |
| Power reduction integrated: | No |
| Installation width (nominal value): | 4,5 mm |
| Valve construction: | Valve complete |
| Switch function: | on/off |
| Electrical connection type: | male |
| Switch time open max.: | 5 ms |
| Switch time close max.: | 5 ms |
| Electrical connection polarity: | left pin positive pole |
| Nominal operation/Duty cycle: | 40 % |
| Coil wiring LED: | No |
| Coil wiring polarity recovery diode redundant: | No |
| Electrical connection sort: | Plug RM 5.08, for connector Type 2504 |
| Electrical connection number of contacts: | 2 |
| Cable plug in delivery: | not included |
| Electrical connection position: | top |
| Limiting power: | 2,2 W |
| Port connection 1 flange: | Bürkert flange 4,5 x 39 version A1 |
| Coil type: | permanently integrated |
| Port connection 2 flange: | Bürkert flange 4,5 x 39 version A1 |
| Coil insulation material (encasement): | LCP |
| Port connection seal material design: | Formed gasket |
| Coil wiring overvoltage protection: | without |
| Coil wiring rectifier: | No |
| Coil wiring polarity recovery diode: | No |
| Mounting (flange) type: | Metric screws |
| Mounting (flange) material: | Stainless steel |
| Coil wiring polarity protection: | No |
| Rated power DC: | 5,7 W |
Technical Specifications
- 0,80 mm
- -1,00 bar - 3,00 bar - A - normally closed - inlet port 1 (P/NC)
- direct-acting
- 24,00 V - 24,00 V
- 15,00 °C - 50,00 °C
- PEEK (Polyetheretherketone)
- FFKM (Perfluoroelastomer rubber)
Description
With a center-to-center spacing of just 4.5 mm, Type 6650 sets a new benchmark in the miniaturization of media-separated solenoid valves. The consistently optimized design enables reproducible, precise dosing while providing good flushability. Thanks to high-quality materials, the valve is also suitable for use with aggressive chemicals.
Available in the two nominal sizes 0.4 and 0.8 mm, Type 6650 is designed for maximum fluidic performance combined with minimal space requirements. The slim 4.5 mm center-to-center spacing opens up new application possibilities, particularly for dosing into 384-well microtiter plates. Technically, the valve is based on the proven rocker/flap armature principle of Type 0330, thereby continuing the success story of the legendary Type 0127.
- Center-to-center spacing of only 4.5 mm
- Media-separated design for aggressive media
- Direct-acting operating principle
- Suitable for vacuum applications up to 7 bar
- Fast-switching
Your Benefits
- Worldwide shipping for all valves and measuring instruments
- Large stock levels for many products – just ask us for current lead times
- Spare parts and service kits are also available
- Fast delivery from stock via UPS (parcel) or DSV (pallet), express shipping available on request
- Extensive application know-how built on years of practical experience
- Personal advice on choosing the right component
- Resellers receive volume-based trade discounts on request – just get in touch with us directly
- Large enterprises, public authorities and government bodies can order on account – please contact us via our contact form
Christian Bürkert GmbH & Co. KG, Christian-Bürkert-Straße 13-17, 74653 Ingelfingen, Baden-Württemberg, Deutschland, [email protected], https://www.buerkert.de
Manufacturer according to GPSR
Christian Bürkert GmbH & Co. KG, Christian-Bürkert-Straße13-17, 74653 Ingelfingen, Baden-Württemberg, Deutschland, [email protected], https://www.buerkert.de
